#
# This file adds to the values in AR933X_BASE.hints.
#

# mdiobus on arge1
hint.argemdio.0.at="nexus0"
hint.argemdio.0.maddr=0x1a000000
hint.argemdio.0.msize=0x1000
hint.argemdio.0.order=0

# Embedded Atheros Switch
hint.arswitch.0.at="mdio0"

# XXX this should really say it's an AR933x switch, as there
# are some vlan specific differences here!
hint.arswitch.0.is_7240=1
hint.arswitch.0.numphys=4
hint.arswitch.0.phy4cpu=1	# phy 4 is a "CPU" separate PHY
hint.arswitch.0.is_rgmii=0
hint.arswitch.0.is_gmii=1	# arge1 <-> switch PHY is GMII

# arge0 - MII, autoneg, phy(4)
hint.arge.0.phymask=0x10	# PHY4
hint.arge.0.mdio=mdioproxy1	# .. off of the switch mdiobus
hint.arge.0.eeprommac=0x1fff0000

# arge1 - GMII, 1000/full
hint.arge.1.phymask=0x0		# No directly mapped PHYs
hint.arge.1.media=1000
hint.arge.1.fduplex=1
hint.arge.1.eeprommac=0x1fff0006

# ath0
hint.ath.0.eepromaddr=0x1fff0000
hint.ath.0.eepromsize=16384

# 16MB flash layout:
# [    0.510000] 5 tp-link partitions found on MTD device spi0.0
# [    0.510000] Creating 5 MTD partitions on "spi0.0":
# [    0.520000] 0x000000000000-0x000000020000 : "u-boot"
# [    0.520000] 0x000000020000-0x000000136468 : "kernel"
# [    0.530000] 0x000000136468-0x000000ff0000 : "rootfs"
# [    0.530000] mtd: device 2 (rootfs) set to be root filesystem
# [    0.540000] 1 squashfs-split partitions found on MTD device rootfs
# [    0.540000] 0x000000730000-0x000000fe0000 : "rootfs_data"
# [    0.540000] 0x000000fe0000-0x000000ff0000 : "nvram"
# [    0.550000] 0x000000ff0000-0x000001000000 : "art"
# [    0.560000] 0x000000020000-0x000000fe0000 : "firmware"

# 64KiB uboot
hint.map.0.at="flash/spi0"
hint.map.0.start=0x00000000
hint.map.0.end=0x00010000
hint.map.0.name="u-boot"
hint.map.0.readonly=1

# 64KiB uboot
hint.map.1.at="flash/spi0"
hint.map.1.start=0x00010000
hint.map.1.end=0x00020000
hint.map.1.name="uboot-env"
hint.map.1.readonly=1

# kernel
hint.map.2.at="flash/spi0"
hint.map.2.start=0x00020000
hint.map.2.end="search:0x00020000:0x10000:.!/bin/sh"
hint.map.2.name="kernel"
hint.map.2.readonly=1

# rootfs ulzma
hint.map.3.at="flash/spi0"
hint.map.3.start="search:0x00020000:0x10000:.!/bin/sh"
hint.map.3.end=0x00fe0000
hint.map.3.name="rootfs"
hint.map.3.readonly=1

# 64KiB cfg
hint.map.4.at="flash/spi0"
hint.map.4.start=0x00fe0000
hint.map.4.end=0x00ff0000
hint.map.4.name="cfg"
hint.map.4.readonly=0

# all firmware 16000KiB
hint.map.5.at="flash/spi0"
hint.map.5.start=0x00020000
hint.map.5.end=0x00ff0000
hint.map.5.name="firmware"
hint.map.5.readonly=0

# 64KiB ART
hint.map.6.at="flash/spi0"
hint.map.6.start=0x00ff0000
hint.map.6.end=0x01000000
hint.map.6.name="ART"
hint.map.6.readonly=1

# GPIO
hint.gpio.0.pinmask=0x0c8ff1c3

hint.gpioled.0.at="gpiobus0"
hint.gpioled.0.pins=0x08000000
hint.gpioled.0.name="board"
hint.gpioled.0.invert=0

#Red
hint.gpioled.1.at="gpiobus0"
hint.gpioled.1.pins=0x00020000
hint.gpioled.1.name="red"
hint.gpioled.1.invert=0

#Green
hint.gpioled.2.at="gpiobus0"
hint.gpioled.2.pins=0x00010000
hint.gpioled.2.name="green"
hint.gpioled.2.invert=0

#Blue
hint.gpioled.3.at="gpiobus0"
hint.gpioled.3.pins=0x00008000
hint.gpioled.3.name="blue"
hint.gpioled.3.invert=0

# I2C
# 0x20 - 0x27 = Relay Controllers (0x27 is default)
# 0x5a = PWM/Servo Controller
hint.gpioiic.0.at="gpiobus0"
hint.gpioiic.0.pins=0x300000 # pins 20 and 21
hint.gpioiic.0.scl=0 # pin 20
hint.gpioiic.0.sda=1 # pin 21