# arge0 is connected to the LAN side of the switch PHY.
# arge1 is connected to the single port WAN side of the switch PHY.

hint.arge.0.phymask=0x0
hint.arge.0.media=1000
hint.arge.0.fduplex=1
hint.arge.0.eeprommac=0x1f66ffa0
hint.arge.0.readascii=1

hint.arge.1.phymask=0x0
hint.arge.1.media=1000
hint.arge.1.fduplex=1
hint.arge.1.eeprommac=0x1f66ffb4
hint.arge.1.readascii=1

# ath0 - slot 17
hint.pcib.0.bus.0.17.0.ath_fixup_addr=0x1f661000
hint.pcib.0.bus.0.17.0.ath_fixup_size=4096

# ath1 - slot 18
hint.pcib.0.bus.0.18.0.ath_fixup_addr=0x1f665000
hint.pcib.0.bus.0.18.0.ath_fixup_size=4096

# .. and now, telling each ath(4) NIC where to find the firmware
# image.
hint.ath.0.eeprom_firmware="pcib.0.bus.0.17.0.eeprom_firmware"
hint.ath.1.eeprom_firmware="pcib.0.bus.0.18.0.eeprom_firmware"

# Geom MAP

# The DIR-825B1 has an 8MB flash part - HOWEVER, the 64k caldata isn't
# at the end of the flash. It's ~ 6MB into the flash image.

# mtdparts=ar7100-nor0:256k(uboot),64k(Config),1024k(vmlinux),5184k(rootfs),
#          64k(caldata)

hint.map.0.at="flash/spi0"
hint.map.0.start=0x00000000
hint.map.0.end=0x000040000
hint.map.0.name="uboot"
hint.map.0.readonly=1

# This config partition is the D-Link specific configuration area.
# I'm re-purposing it for FreeBSD.
hint.map.1.at="flash/spi0"
hint.map.1.start=0x00040000
hint.map.1.end=0x00050000
hint.map.1.name="cfg"
hint.map.1.readonly=0

hint.map.2.at="flash/spi0"
hint.map.2.start=0x0050000
hint.map.2.end="search:0x00050000:0x10000:.!/bin/sh"
hint.map.2.name="kernel"
hint.map.2.readonly=1

hint.map.3.at="flash/spi0"
hint.map.3.start="search:0x00050000:0x10000:.!/bin/sh"
hint.map.3.end=0x00660000
hint.map.3.name="rootfs"
hint.map.3.readonly=0

hint.map.4.at="flash/spi0"
hint.map.4.start=0x00660000
hint.map.4.end=0x00670000
hint.map.4.name="art"
hint.map.4.readonly=1

# GPIO specific configuration block

# Don't flip on anything that isn't already enabled.
# This includes leaving the SPI CS1/CS2 pins as GPIO pins as they're
# not used here.
hint.gpio.0.function_set=0x00000000

hint.gpio.0.function_clear=0x00000000

# These are the GPIO LEDs and buttons which can be software controlled.
hint.gpio.0.pinmask=0x000009ff

# Pin 1  - USB (LED blue)     --> works
# Pin 2  - Power (LED orange) --> works
# Pin 3  - Power (LED blue)   --> works
# Pin 4  - Button (RESET)     --> works
# Pin 5  - WPS (LED blue)     --> works
# Pin 6  - RTL8366RB switch data line
# Pin 7  - Planet (LED orange)--> works
# Pin 8  - RTL8366RB switch clock line
# Pin 9  - Button (WPS)       --> works after set to high
# Pin 10 - N/C
# Pin 11 - N/C
# Pin 12 - Planet (LED blue)  --> works

# LEDs are configured separately and driven by the LED device
# usb tested good
hint.gpioled.0.at="gpiobus0"
hint.gpioled.0.name="usb-blue"
hint.gpioled.0.pins=0x0001

# no orange power led?
hint.gpioled.1.at="gpiobus0"
hint.gpioled.1.name="power-orange"
hint.gpioled.1.pins=0x0002

# blue power tested good
hint.gpioled.2.at="gpiobus0"
hint.gpioled.2.name="power-blue"
hint.gpioled.2.pins=0x0004

# wps tested good
hint.gpioled.3.at="gpiobus0"
hint.gpioled.3.name="wps-blue"
hint.gpioled.3.pins=0x0010

# orage globe tested good
hint.gpioled.4.at="gpiobus0"
hint.gpioled.4.name="planet-orange"
hint.gpioled.4.pins=0x0040

# no blue planet LED on this unit
hint.gpioled.5.at="gpiobus0"
hint.gpioled.5.name="planet-blue"
hint.gpioled.5.pins=0x0800

# GPIO I2C bus
hint.gpioiic.0.at="gpiobus0"
hint.gpioiic.0.pins=0x00a0
hint.gpioiic.0.sda=0
hint.gpioiic.0.scl=1

# I2C bus
# Don't be strict about I2C protocol - the relaxed semantics are required
# by the realtek switch PHY.
hint.iicbus.0.strict=0

# Bit bang bus - override default delay
#hint.iicbb.0.udelay=3